Blog: What codes matter for electrical safety in hazardous areas?

• For Safety's Sake: What codes matter for electrical safety in hazardous areas?

Get in the zone for safety in hazardous areas

Setting the record straight: equipment safety in hazardous areas

Primer on zone equipment certification

The Zone method has become a worldwide accepted practice for classifying hazardous location classified areas. The International Electrotechnical Commission System for certification to standards relating to equipment for use in explosive atmospheres (IECEx System) lists 62 countries that are full members and an additional 26 as associate members. Many countries have their own directives and certification requirements for equipment approvals within their borders.

The Zone method dates back to 1996 and was first introduced by the NEC, National Fire Protection Association (NFPA) with Article 505. It allows for parallel classification in the traditional NEC Article 500 Division system.

In this division system, Zone terminology was used as the international system for classification of hazardous locations containing flammable gasses, liquids or vapors, combustible dust, or ignitable flyings, which divided classified areas into three segments: Zone 0, Zone 1, or Zone 2 for gases/ vapors, and Zone 20, Zone 21, Zone 22, for combustible dust and ignitable flyings.

Today, Zone rated equipment still requires certification of ordinary location requirements in the U.S. The AEx marking, developed by the American National Standards Institute (ANSI) and International Society of Automation (ISA), ensures that Zone equipment conforms with hazardous location requirements and the general ordinary location American safety standards. As such, the AEx symbol is a critical marking requirement within the Zone material nomenclature.

What if an AEx-Zone or Division certified technology isn't available?

The NEC Article 500.8(A) addresses this possibility and indicates that the suitability of equipment is determined by one of the following:

• equipment listing
• evidence of equipment evaluation from a qualified testing lab or AHJ, or
• evidence acceptable to the AHJ like a manufacturer's self-evaluation or owner's engineering judgement.
  

In our view, a manufacturer's self-certification and owner's engineering judgement must be carefully reviewed and only be considered when the decision maker is fully confident that ordinary safety standards have been achieved. This evidence must also be accepted by the AHJ.

Further, OSHA provides additional guidance and requirements for product allowance. OSHA 29 CFR 1910.399 defines equipment acceptable for hazardous environments if it is:

1. Determined safe by a nationally recognized testing lab
2. Inspected by another federal agency, or by a state, municipal or other local authority responsible for enforcing occupational safety provisions of the NEC and found in compliance with the NEC
3. Determined to be safe (for it's intended use) by the manufacturer, based on test data, that the employer keeps and can provide for inspection purposes.

Zone method rated equipment: marked with AEx, listed by a nationally recognized testing lab

The OSHA and NEC allowances permit for a product to be approved for installation without third-party testing by a nationally recognized testing lab (NRTL); OSHA lists 19 NRTLs on their website, including UL, CSA, ETL-Intertek and FM.

However and importantly, both the OSHA and NEC language indicate the general rule is that equipment should be tested and listed by a NRTL-unless these avenues have been exhausted.

When thinking about electrical equipment without testing by a NRTL, it's important to consider:

• Does the state or municipality where equipment is being installed have requirements only allowing for the installation of third-party evaluated equipment?
• Does the customer facility have requirements only allowing for installation of third-party NRTL evaluated equipment?
• Who is shouldering the liability for the owner's engineering judgement or self-evaluated equipment for suitability of ordinary and hazardous-area locations?

Facilities using the NEC Articles 505 and 506 Zone classification of hazardous location classified areas are governed by the approval requirements outlined in the NEC articles for the wiring methods and equipment certification.

When zone method rated equipment includes the AEx marking, it means the equipment is certified to the American standards per NEC Article 505.9 (C) and Article 506.9 (C). That AEx marking ensures the Zone equipment conforms with both hazardous location requirements and general safety American standards for ordinary locations. These certifications give customers confidence and trust in the equipment they're applying.

More for you

• Healthcare Blog: Creating more resilient healthcare environments }

  Healthcare

  Blog: Creating more resilient healthcare environments

• Standards help utilities address wildfire risk Wildfire codes and standards support a safer grid }

  Standards help utilities address wildfire risk

  Wildfire codes and standards support a safer grid

• Testing and fire codes for safe energy storage Safe energy storage is critical for a low-carbon energy future }

  Testing and fire codes for safe energy storage

  Safe energy storage is critical for a low-carbon energy future